[27214.535307] rt2870sta: module is from the staging directory, the quality is unknown, you have been warned.
[27214.537342] rtusb init --->
[27214.537380] usbcore: registered new interface driver rt2870
[27409.120657] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[27538.076667] ADDRCONF(NETDEV_UP): wlan0: link is not ready
lsusb:
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 002: ID 046d:08d7 Logitech, Inc. QuickCam Communicate STX
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 015: ID 7392:7718
Bus 001 Device 007: ID 046d:09a2 Logitech, Inc. QuickCam Communicate Deluxe/S7500
Bus 001 Device 006: ID 1267:0103 Logic3 / SpectraVideo plc G-720 Keyboard
Bus 001 Device 005: ID 046d:c01e Logitech, Inc. MX518 Optical Mouse
Bus 001 Device 004: ID 03f0:7e04 Hewlett-Packard DeskJet F4100 Printer series
Bus 001 Device 003: ID 04cc:1521 Philips Semiconductors USB 2.0 Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
(note that nothing else shows up for that device)
iwconfig:
lo no wireless extensions.
eth0 no wireless extensions.
wmaster0 no wireless extensions.
wlan0 IEEE 802.11bgn ESSID:"" Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated Tx-Power=16 dBm
Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off
Power Management:on
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
Running:
Ubuntu 9.10 RC - Karmic
Edimax ew7718UN
Device is seen as wlan0 instead of ra0 as it should. Using Wicd, I can set it to ra0 which allows my own network to show up, but it will not connect. Help.
No go, the blacklisting does not work for me.
From dmesg:
[27214.535307] rt2870sta: module is from the staging directory, the quality is unknown, you have been warned. NETDEV_ UP): wlan0: link is not ready NETDEV_ UP): wlan0: link is not ready
[27214.537342] rtusb init --->
[27214.537380] usbcore: registered new interface driver rt2870
[27409.120657] ADDRCONF(
[27538.076667] ADDRCONF(
lsusb:
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 002: ID 046d:08d7 Logitech, Inc. QuickCam Communicate STX
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 015: ID 7392:7718
Bus 001 Device 007: ID 046d:09a2 Logitech, Inc. QuickCam Communicate Deluxe/S7500
Bus 001 Device 006: ID 1267:0103 Logic3 / SpectraVideo plc G-720 Keyboard
Bus 001 Device 005: ID 046d:c01e Logitech, Inc. MX518 Optical Mouse
Bus 001 Device 004: ID 03f0:7e04 Hewlett-Packard DeskJet F4100 Printer series
Bus 001 Device 003: ID 04cc:1521 Philips Semiconductors USB 2.0 Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
(note that nothing else shows up for that device)
iwconfig:
lo no wireless extensions.
eth0 no wireless extensions.
wmaster0 no wireless extensions.
wlan0 IEEE 802.11bgn ESSID:""
Mode: Managed Frequency:2.412 GHz Access Point: Not-Associated
Tx-Power= 16 dBm
Encryption key:off
Retry long limit:7 RTS thr:off Fragment thr:off
Power Management:on
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
Running:
Ubuntu 9.10 RC - Karmic
Edimax ew7718UN
Device is seen as wlan0 instead of ra0 as it should. Using Wicd, I can set it to ra0 which allows my own network to show up, but it will not connect. Help.