Corrections:
Windows: SCSI 0,0,0 Seagate ST380817AS 80 GB HD SCSI 0,1,0 Seagate ST380813AS 80 GB HD <--- SCSI 1,0,0 Seagate ST3250820AS 250 GB HD
And to make it clear, I'm not actually using any kind of RAID, just that the mobo is capable of it.
The relevant part of lspci -vv shows this:
00:12.0 SATA controller: ATI Technologies Inc SB600 Non-Raid-5 SATA (prog-if 01 [AHCI 1.0]) Subsystem: ASUSTeK Computer Inc. Unknown device 81ef Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Interrupt: pin A routed to IRQ 22 Region 0: I/O ports at ff00 [size=8] Region 1: I/O ports at fe00 [size=4] Region 2: I/O ports at fd00 [size=8] Region 3: I/O ports at fc00 [size=4] Region 4: I/O ports at fb00 [size=16] Region 5: Memory at fe02f000 (32-bit, non-prefetchable) [size=1K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [70] #12 [0010]
[...]
00:14.1 IDE interface: ATI Technologies Inc SB600 IDE (prog-if 8a [Master SecP PriP]) Subsystem: ASUSTeK Computer Inc. Unknown device 81ef Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at 01f0 [size=8] Region 1: I/O ports at 03f4 [size=1] Region 2: I/O ports at 0170 [size=8] Region 3: I/O ports at 0374 [size=1] Region 4: I/O ports at f900 [size=16] Capabilities: [70] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable- Address: 00000000 Data: 0000
Corrections:
Windows:
SCSI 0,0,0 Seagate ST380817AS 80 GB HD
SCSI 0,1,0 Seagate ST380813AS 80 GB HD <---
SCSI 1,0,0 Seagate ST3250820AS 250 GB HD
And to make it clear, I'm not actually using any kind of RAID, just that the mobo is capable of it.
The relevant part of lspci -vv shows this:
00:12.0 SATA controller: ATI Technologies Inc SB600 Non-Raid-5 SATA (prog-if 01 [AHCI 1.0])
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0- ,D1-,D2- ,D3hot- ,D3cold- )
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [70] #12 [0010]
Subsystem: ASUSTeK Computer Inc. Unknown device 81ef
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at ff00 [size=8]
Region 1: I/O ports at fe00 [size=4]
Region 2: I/O ports at fd00 [size=8]
Region 3: I/O ports at fc00 [size=4]
Region 4: I/O ports at fb00 [size=16]
Region 5: Memory at fe02f000 (32-bit, non-prefetchable) [size=1K]
[...]
00:14.1 IDE interface: ATI Technologies Inc SB600 IDE (prog-if 8a [Master SecP PriP])
Capabilities: [70] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-
Address: 00000000 Data: 0000
Subsystem: ASUSTeK Computer Inc. Unknown device 81ef
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at f900 [size=16]