Ubuntu
linux-firmware package

Edimax EW-7318Ug stopped working after upgrading to the latest kernel

Bug #284005 reported by Edward Karavakis
2
Affects Status Importance Assigned to Milestone
linux-firmware (Ubuntu)
Invalid
Undecided
Unassigned

Bug Description

Binary package hint: linux-firmware

Edimax EW-7318Ug stopped working suddenly after upgrading to the latest kernel today.

Disconnecting the wifi usb stick:

[ 1000.127146] usb 1-2: USB disconnect, address 3
[ 1000.130952] phy1 -> rt2x00usb_vendor_request: Error - Vendor Request 0x07 failed for offset 0x3040 with error -19.
[ 1000.132484] phy1 -> rt2x00usb_vendor_request: Error - Vendor Request 0x06 failed for offset 0x3040 with error -19.
[ 1000.134280] phy1 -> rt2x00usb_vendor_request: Error - Vendor Request 0x06 failed for offset 0x3028 with error -19.
[ 1000.135522] phy1 -> rt2x00usb_vendor_request: Error - Vendor Request 0x06 failed for offset 0x3064 with error -19.
[ 1000.135531] phy1 -> rt2x00usb_vendor_request: Error - Vendor Request 0x0c failed for offset 0x0000 with error -19.
[ 1000.138305] phy1 -> rt2x00usb_vendor_request: Error - Vendor Request 0x0a failed for offset 0x0000 with error -19.
[ 1000.139651] phy1 -> rt2x00usb_vendor_request: Error - Vendor Request 0x0a failed for offset 0x0000 with error -19.
[ 1000.141285] phy1 -> rt2x00usb_vendor_request: Error - Vendor Request 0x0a failed for offset 0x0000 with error -19.
[ 1000.142624] phy1 -> rt2x00usb_vendor_request: Error - Vendor Request 0x0a failed for offset 0x0000 with error -19.

Connecting the wifi usb stick:

[ 1048.860044] usb 1-2: new high speed USB device using ehci_hcd and address 5
[ 1049.155226] usb 1-2: configuration #1 chosen from 1 choice
[ 1049.268747] phy2 -> rt2500usb_init_eeprom: Error - Invalid RT chipset detected.
[ 1049.268758] phy2 -> rt2x00lib_probe_dev: Error - Failed to allocate device.
[ 1049.538714] phy3: Selected rate control algorithm 'pid'
[ 1049.542064] Registered led device: rt73usb-phy3:radio
[ 1049.542452] Registered led device: rt73usb-phy3:assoc
[ 1049.542627] Registered led device: rt73usb-phy3:quality
[ 1049.573147] udev: renamed network interface wlan0 to wlan1

Trying to connect to my wireless network:

[ 1053.604571] firmware: requesting rt73.bin
[ 1053.694864] ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 1060.300446] wlan1: authenticate with AP 00:11:f5:a2:1d:28
[ 1060.302455] wlan1: authenticated
[ 1060.302462] wlan1: associate with AP 00:11:f5:a2:1d:28
[ 1060.305072] wlan1: RX AssocResp from 00:11:f5:a2:1d:28 (capab=0x411 status=0 aid=2)
[ 1060.305078] wlan1: associated
[ 1060.306054] ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 1070.956012] wlan1: no IPv6 routers present
[ 1106.531612] wlan1: disassociating by local choice (reason=3)

Not quite sure if it's linux-firmware or linux-image-generic fault.

See original description
Edward Karavakis (edward-karavakis)
description: updated
description: updated
Revision history for this message
Edward Karavakis (edward-karavakis) wrote :

Worked fine after a couple of hours and a couple of reboots.

Changed in linux-firmware:
status: New → Invalid
To post a comment you must log in.
This report contains Public information  
Everyone can see this information.
Subscribing...

Other bug subscribers

Remote bug watches

Bug watches keep track of this bug in other bug trackers.