Could you verify if ndisgtk/ndiswrapper INF bypass works? Use modprobe to
list active driver module and blacklist it.
On 11 Oct 2010 15:06, "Daniel Cardin" <email address hidden> wrote:
> I have a fresh install of 10.10 and I am experimenting the disabled
wireless problem as well.
> But, on my Dell Vostro 1720, I cannot change the state of the rfkill using
unblock all. It remains blocked.
>
> On the other hand, the wireless IS working as using wicd works just
> fine, where NM fails.
>
> sudo ifconfig eth1 up does not report any error works
>
> daniel@daniel-Vostro-1720:~$ rfkill list
> 0: hci0: Bluetooth
> Soft blocked: no
> Hard blocked: no
> 1: dell-wifi: Wireless LAN
> Soft blocked: yes
> Hard blocked: yes
> 2: dell-bluetooth: Bluetooth
> Soft blocked: no
> Hard blocked: no
>
> No change after sudo rfkill unblock all
>
> The chip is a broadcom 4322, but this seems unrelated. Looks like an
> interaction with the BIOS killswitch info. There was a similar bug which
> affected Dell laptops that was raised against Lucid : bug #430809
>
> --
> Atheros AR928X not connecting on wireless HP G60-468CA
> https://bugs.launchpad.net/bugs/644452
> You received this bug notification because you are a direct subscriber
> of the bug.
>
> Status in “linux” package in Ubuntu: New
>
> Bug description:
> Hello,
>
> this bug concerns my HP G60-468CA laptop. Since testing maverick amd64,
the wireless button switch stays orange and refuses to turn blue to
activate, and the wireless acess is greyed out on both gnome and KDE (Ubuntu
and Kubuntu respectively) running on the latest 2.6.35 kernel. Installing
the latest mainline kernal hangs on boot for all GRUB options (2.6.36-rc4)
and renders sytem unusable.
>
> All terminal configs failed to make this work (lspci and modprobe say that
ath9k is in use and hardware is running and present...
>
> Lucid lynx worked flawlessly.. I even popped the wireless hatch open to
manually remove the wireless card and verify output again...
>
> Please help!
>
> (It might be a duplicate since the report failed on timeout on my last
attempt to submit)
>
>
> Output:
>
> nathanel@Solace:~$ lspci -vnvn
> 00:00.0 RAM memory [0500]: nVidia Corporation MCP78S [GeForce 8200] Memory
Controller [10de:0754] (rev a2)
> Subsystem: Hewlett-Packard Company Device [103c:360a]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Capabilities: <access denied>
>
> 00:01.0 ISA bridge [0601]: nVidia Corporation Device [10de:075e] (rev a2)
> Subsystem: Hewlett-Packard Company Device [103c:360a]
> Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Region 0: I/O ports at 1a00 [size=256]
>
> 00:01.1 SMBus [0c05]: nVidia Corporation MCP78S [GeForce 8200] SMBus
[10de:0752] (rev a1)
> Subsystem: Hewlett-Packard Company Device [103c:360a]
> Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
> Interrupt: pin A routed to IRQ 10
> Region 0: I/O ports at 3080 [size=64]
> Region 4: I/O ports at 3040 [size=64]
> Region 5: I/O ports at 3000 [size=64]
> Capabilities: <access denied>
> Kernel driver in use: nForce2_smbus
> Kernel modules: i2c-nforce2
>
> 00:01.3 Co-processor [0b40]: nVidia Corporation MCP78S [GeForce 8200]
Co-Processor [10de:0753] (rev a2)
> Subsystem: Hewlett-Packard Company Device [103c:360a]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
> Latency: 0 (750ns min, 250ns max)
> Interrupt: pin B routed to IRQ 11
> Region 0: Memory at c0080000 (32-bit, non-prefetchable) [size=512K]
>
> 00:01.4 RAM memory [0500]: nVidia Corporation MCP78S [GeForce 8200] Memory
Controller [10de:0568] (rev a1)
> Subsystem: Hewlett-Packard Company Device [103c:360a]
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
> Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
>
> 00:02.0 USB Controller [0c03]: nVidia Corporation MCP78S [GeForce 8200]
OHCI USB 1.1 Controller [10de:077b] (rev a1) (prog-if 10 [OHCI])
> Subsystem: Hewlett-Packard Company Device [103c:360a]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
> Latency: 0 (750ns min, 250ns max)
> Interrupt: pin A routed to IRQ 17
> Region 0: Memory at c0006000 (32-bit, non-prefetchable) [size=4K]
> Capabilities: <access denied>
> Kernel driver in use: ohci_hcd
>
> 00:02.1 USB Controller [0c03]: nVidia Corporation MCP78S [GeForce 8200]
EHCI USB 2.0 Controller [10de:077c] (rev a1) (prog-if 20 [EHCI])
> Subsystem: Hewlett-Packard Company Device [103c:360a]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
> Latency: 0 (750ns min, 250ns max)
> Interrupt: pin B routed to IRQ 17
> Region 0: Memory at c0007000 (32-bit, non-prefetchable) [size=256]
> Capabilities: <access denied>
> Kernel driver in use: ehci_hcd
>
> 00:04.0 USB Controller [0c03]: nVidia Corporation MCP78S [GeForce 8200]
OHCI USB 1.1 Controller [10de:077d] (rev a1) (prog-if 10 [OHCI])
> Subsystem: Hewlett-Packard Company Device [103c:360a]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
> Latency: 0 (750ns min, 250ns max)
> Interrupt: pin A routed to IRQ 16
> Region 0: Memory at c0008000 (32-bit, non-prefetchable) [size=4K]
> Capabilities: <access denied>
> Kernel driver in use: ohci_hcd
>
> 00:04.1 USB Controller [0c03]: nVidia Corporation MCP78S [GeForce 8200]
EHCI USB 2.0 Controller [10de:077e] (rev a1) (prog-if 20 [EHCI])
> Subsystem: Hewlett-Packard Company Device [103c:360a]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
> Latency: 0 (750ns min, 250ns max)
> Interrupt: pin B routed to IRQ 16
> Region 0: Memory at c0007400 (32-bit, non-prefetchable) [size=256]
> Capabilities: <access denied>
> Kernel driver in use: ehci_hcd
>
> 00:06.0 IDE interface [0101]: nVidia Corporation MCP78S [GeForce 8200] IDE
[10de:0759] (rev a1) (prog-if 8a [Master SecP PriP])
> Subsystem: Hewlett-Packard Company Device [103c:360a]
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx+
> Latency: 0 (750ns min, 250ns max)
> Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
> Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
> Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
> Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1]
> Region 4: I/O ports at 30c0 [size=16]
> Capabilities: <access denied>
> Kernel driver in use: pata_amd
> Kernel modules: pata_amd
>
> 00:07.0 Audio device [0403]: nVidia Corporation
MCP72XE/MCP72P/MCP78U/MCP78S High Definition Audio [10de:0774] (rev a1)
> Subsystem: Hewlett-Packard Company Device [103c:360a]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
> Latency: 0 (500ns min, 1250ns max)
> Interrupt: pin A routed to IRQ 19
> Region 0: Memory at c0000000 (32-bit, non-prefetchable) [size=16K]
> Capabilities: <access denied>
> Kernel driver in use: HDA Intel
> Kernel modules: snd-hda-intel
>
> 00:08.0 PCI bridge [0604]: nVidia Corporation MCP78S [GeForce 8200] PCI
Bridge [10de:075a] (rev a1) (prog-if 01 [Subtractive decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
> Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn-
> Capabilities: <access denied>
>
> 00:09.0 IDE interface [0101]: nVidia Corporation MCP78S [GeForce 8200]
SATA Controller (non-AHCI mode) [10de:0ad0] (rev a2) (prog-if 85 [Master
SecO PriO])
> Subsystem: Hewlett-Packard Company Device [103c:360a]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
> Latency: 0 (750ns min, 250ns max)
> Interrupt: pin A routed to IRQ 41
> Region 0: I/O ports at 30f0 [size=8]
> Region 1: I/O ports at 30e4 [size=4]
> Region 2: I/O ports at 30e8 [size=8]
> Region 3: I/O ports at 30e0 [size=4]
> Region 4: I/O ports at 30d0 [size=16]
> Region 5: Memory at c0004000 (32-bit, non-prefetchable) [size=8K]
> Capabilities: <access denied>
> Kernel driver in use: ahci
> Kernel modules: ahci
>
> 00:0a.0 Ethernet controller [0200]: nVidia Corporation MCP77 Ethernet
[10de:0760] (rev a2)
> Subsystem: Hewlett-Packard Company Device [103c:360a]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
> Latency: 0 (250ns min, 5000ns max)
> Interrupt: pin A routed to IRQ 42
> Region 0: Memory at c0009000 (32-bit, non-prefetchable) [size=4K]
> Region 1: I/O ports at 30f8 [size=8]
> Region 2: Memory at c0007c00 (32-bit, non-prefetchable) [size=256]
> Region 3: Memory at c0007800 (32-bit, non-prefetchable) [size=16]
> Capabilities: <access denied>
> Kernel driver in use: forcedeth
> Kernel modules: forcedeth
>
> 00:0b.0 PCI bridge [0604]: nVidia Corporation MCP78S [GeForce 8200] PCI
Express Bridge [10de:0569] (rev a1) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
> I/O behind bridge: 00004000-00004fff
> Memory behind bridge: c1000000-c1ffffff
> Prefetchable memory behind bridge: 00000000c4000000-00000000dfffffff
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: <access denied>
> Kernel modules: shpchp
>
> 00:14.0 PCI bridge [0604]: nVidia Corporation MCP78S [GeForce 8200] PCI
Bridge [10de:077a] (rev a1) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Bus: primary=00, secondary=07, subordinate=07, sec-latency=0
> Memory behind bridge: c2000000-c20fffff
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: <access denied>
> Kernel driver in use: pcieport
> Kernel modules: shpchp
>
> 00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] Family 11h
Processor HyperTransport Configuration [1022:1300] (rev 40)
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
> Capabilities: <access denied>
>
> 00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] Family 11h
Processor Address Map [1022:1301]
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
>
> 00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] Family 11h
Processor DRAM Controller [1022:1302]
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
> Kernel modules: amd64_edac_mod
>
> 00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] Family 11h
Processor Miscellaneous Control [1022:1303]
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
> Capabilities: <access denied>
> Kernel driver in use: k10temp
> Kernel modules: k10temp
>
> 00:18.4 Host bridge [0600]: Advanced Micro Devices [AMD] Family 11h
Processor Link Control [1022:1304]
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
>
> 02:00.0 VGA compatible controller [0300]: nVidia Corporation C77 [GeForce
8200M G] [10de:0845] (rev a2) (prog-if 00 [VGA controller])
> Subsystem: Hewlett-Packard Company Device [103c:360a]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Interrupt: pin A routed to IRQ 20
> Region 0: Memory at c1000000 (32-bit, non-prefetchable) [size=16M]
> Region 1: Memory at d0000000 (64-bit, prefetchable) [size=256M]
> Region 3: Memory at c4000000 (64-bit, prefetchable) [size=32M]
> Region 5: I/O ports at 4000 [size=128]
> [virtual] Expansion ROM at c6000000 [disabled] [size=128K]
> Capabilities: <access denied>
> Kernel driver in use: nouveau
> Kernel modules: nouveau, nvidiafb
>
> 07:00.0 Network controller [0280]: Atheros Communications Inc. AR928X
Wireless Network Adapter (PCI-Express) [168c:002a] (rev 01)
> Subsystem: Hewlett-Packard Company Device [103c:1381]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 23
> Region 0: Memory at c2000000 (64-bit, non-prefetchable) [size=64K]
> Capabilities: <access denied>
> Kernel driver in use: ath9k
> Kernel modules: ath9k
>
> ProblemType: Bug
> DistroRelease: Ubuntu 10.10
> Package: linux-image-2.6.35-22-generic 2.6.35-22.33
> Regression: Yes
> Reproducible: No
> ProcVersionSignature: Ubuntu 2.6.35-22.33-generic 2.6.35.4
> Uname: Linux 2.6.35-22-generic x86_64
> AlsaVersion: Advanced Linux Sound Architecture Driver Version 1.0.23.
> Architecture: amd64
> ArecordDevices:
> **** List of CAPTURE Hardware Devices ****
> card 0: NVidia [HDA NVidia], device 0: CONEXANT Analog [CONEXANT Analog]
> Subdevices: 1/1
> Subdevice #0: subdevice #0
> AudioDevicesInUse:
> USER PID ACCESS COMMAND
> /dev/snd/controlC0: ubuntu 4436 F.... pulseaudio
> CRDA: Error: [Errno 2] No such file or directory
> Card0.Amixer.info:
> Card hw:0 'NVidia'/'HDA NVidia at 0xc0000000 irq 19'
> Mixer name : 'Nvidia MCP77/78 HDMI'
> Components : 'HDA:14f15051,103c360a,00100000
HDA:10de0002,10de0101,00100000'
> Controls : 18
> Simple ctrls : 8
> Date: Tue Sep 21 15:08:44 2010
> Frequency: Once a day.
> LiveMediaBuild: Kubuntu 10.10 "Maverick Meerkat" - Alpha amd64 (20100920)
> MachineType: Hewlett-Packard HP G60 Notebook PC
> ProcCmdLine: noprompt cdrom-detect/try-usb=true
file=/cdrom/preseed/khostname.seed boot=casper maybe-ubiquity
initrd=/casper/initrd.lz quiet splash -- BOOT_IMAGE=/casper/vmlinuz
> ProcEnviron:
> LANGUAGE=
> LANG=en_US.UTF-8
> SHELL=/bin/bash
> RelatedPackageVersions: linux-firmware 1.38
> SourcePackage: linux
> dmi.bios.date: 08/18/2009
> dmi.bios.vendor: Hewlett-Packard
> dmi.bios.version: F.54
> dmi.board.name: 303C
> dmi.board.vendor: Wistron
> dmi.board.version: 08.60
> dmi.chassis.type: 10
> dmi.chassis.vendor: Wistron
> dmi.chassis.version: N/A
> dmi.modalias:
dmi:bvnHewlett-Packard:bvrF.54:bd08/18/2009:svnHewlett-Packard:pnHPG60NotebookPC:pvrF.54:rvnWistron:rn303C:rvr08.60:cvnWistron:ct10:cvrN/A:
> dmi.product.name: HP G60 Notebook PC
> dmi.product.version: F.54
> dmi.sys.vendor: Hewlett-Packard
>
> To unsubscribe from this bug, go to:
> https://bugs.launchpad.net/ubuntu/+source/linux/+bug/644452/+subscribe